P200-02L5C-V20-00

Dansion P200 series Dansion P200 series pump P200-02L5C-V20-00 P200-02L5C-V20-00 Features – For use in mobile and stationary applications – The output speed is dependent on the flow of the Dansion P200 series pump P200-02L5C-V20-00 and the displacement of the motor. – The output torque increases with the pressure differential between the high-pressure and the low-pressure side. – Finely graduated sizes permit far-reaching adaptation to thedrive case – High power density – Small dimensions – High total efficiency – Good starting characteristics – Economical design Dansion P200 series Dansion P200 series pump P200-02L5C-V20-00 P200-02L5C-V20-00 has a number of pistons (usually an odd number) arranged in a circular array within a housing which is commonly referred to as a cylinder block, rotor or barrel. This cylinder block is driven to rotate about its axis of symmetry by an integral shaft that is, more or less, aligned with the Dansion P200 series pump P200-02L5C-V20-00ing pistons (usually parallel but not necessarily). Mating surfaces. One end of the cylinder block is convex and wears against a mating surface on a stationary valve plate. The inlet and outlet fluid of the Dansion P200 series Dansion P200 series pump P200-02L5C-V20-00 P200-02L5C-V20-00 pass through different parts of the sliding interface between the cylinder block and valve plate. The valve plate has two semi-circular ports that allow inlet of the operating fluid and exhaust of the outlet fluid respectively. Protruding pistons. The Dansion P200 series pump P200-02L5C-V20-00ing pistons protrude from the opposite end of the cylinder block. There are numerous configurations used for the exposed ends of the pistons but in all cases they bear against a cam. In variable displacement units, the cam is movable and commonly referred to as a swashplate, yoke or hanger. For conceptual purposes, the cam can be represented by a plane, the orientation of which, in combination with shaft rotation, provides the cam action that leads to piston reciprocation and thus Dansion P200 series pump P200-02L5C-V20-00ing. The angle between a vector normal to the cam plane and the cylinder block axis of rotation, called the cam angle, is one variable that determines the displacement of the Dansion P200 series pump P200-02L5C-V20-00 or the amount of fluid Dansion P200 series pump P200-02L5C-V20-00ed per shaft revolution. Variable displacement units have the ability to vary the cam angle during operation whereas fixed displacement units do not. Reciprocating pistons. As the cylinder block rotates, the exposed ends of the pistons are constrained to follow the surface of the cam plane. Since the cam plane is at an angle to the axis of rotation, the pistons must reciprocate axially as they precess about the cylinder block axis. The axial motion of the pistons is sinusoidal. During the rising portion of the piston's reciprocation cycle, the piston moves toward the valve plate. Also, during this time, the fluid trapped between the buried end of the piston and the valve plate is vented to the Dansion P200 series pump P200-02L5C-V20-00's discharge port through one of the valve plate's semi-circular ports - the discharge port. As the piston moves toward the valve plate, fluid is pushed or displaced through the discharge port of the valve plate. Effect of precession. When the piston is at the top of the reciprocation cycle (commonly referred to as top-dead-center or just TDC), the connection between the trapped fluid chamber and the Dansion P200 series pump P200-02L5C-V20-00's discharge port is closed. Shortly thereafter, that same chamber becomes open to the Dansion P200 series pump P200-02L5C-V20-00's inlet port. As the piston continues to precess about the cylinder block axis, it moves away from the valve plate thereby increasing the volume of the trapped chamber. As this occurs, fluid enters the chamber from the Dansion P200 series pump P200-02L5C-V20-00's inlet to fill the void. This process continues until the piston reaches the bottom of the reciprocation cylinder - commonly referred to as bottom-dead-center or BDC. At BDC, the connection between the Dansion P200 series pump P200-02L5C-V20-00ing chamber and inlet port is closed. Shortly thereafter, the chamber becomes open to the discharge port again and the Dansion P200 series pump P200-02L5C-V20-00ing cycle starts over. Dansion P200 series Dansion P200 series pump P200-02L5C-V20-00 P200-02L5C-V20-00 are used to power the hydraulic systems of jet aircraft, being gear-driven off of the turbine engine's main shaft, The system used on the F-14 used a 9-piston Dansion P200 series pump P200-02L5C-V20-00 that produced a standard system operating pressure of 3000 psi and a maximum flow of 84 gallons per minute. They are also used in some pressure washers. For example Dansion P200 Dansion P200 series pump P200-02L5C-V20-00 has several models powered by axial piston Dansion P200 series pump P200-02L5C-V20-00s with three pistons. Axial reciprocating motors are also used to power many machines. They operate on the same principle as described above, except that the circulating fluid is provided under considerable pressure and the piston housing is made to rotate and provide shaft power to another machine. A common use of an axial reciprocating motor is to power small earthmoving plant such as skid loader machines. Another use is to drive the screws of torpedoes. Hydraulic Equipment Distributor Supplier is the global leader in motion and control technologies, providing precision-engineered solutions for a wide variety of mobile, industrial and aerospace markets. Hydraulic Equipment Distributor Supplier can be found on and around everything that moves. At Hydraulic Equipment Distributor Supplier we have an unmatched breadth and depth of Dansion P200 series pump P200-02L5C-V20-00s that originate from a global leadership position in nine core Motion and Control technologies that include aerospace, climate control, electromechanical, filtration, fluid and gas handling, hydraulics, pneumatics, process control, sealing and shielding. We can apply these Dansion P200 series pump P200-02L5C-V20-00s and technologies individually to solve customer challenges that are simpler, or we can combine them to develop systems that address challenges that are complex.

Hydraulic motor, Hydraulic pump, Gear pump, Gearbox, Hydraulic spare parts, Piston motor, Piston pump